Softened Water Tastes Salty? This Could Be Why

Conventional water softeners are the best for those who prefer the taste of their tap water. With them, you add a small amount of salt during the softening process. Sodium is an essential mineral that helps prevent the hardening of teeth. It also helps the body absorb other minerals, including those needed to protect bones.

You shouldn’t be able to taste the salt in your water. Your water should have 18 grains of hardness per gallon. A water softener adds about 35 milligrams of sodium to an 8-ounce glass of water.

In the context of your body, one slice of bread contains between 100 and 230 mg of sodium. Your softener water tastes salty because you are using too much. It’s not pleasant to drink salty water, and once you’ve had enough you’ll want to stop drinking it.

I’ll look at the possible causes of salty water after regeneration and how to fix them.

What Causes Salty Water After Regeneration?

There are lots of myths about water softeners, like they make your water taste salty, but they are not true. Your water will still be good to drink.

There’s a good chance that if you can taste salt, there’s clearly something wrong. Salt water regeneration (also known as “recharging”) may not always produce the amount of water that you need to drink.

Take precautions when diagnosing issues, so that you don’t end up working in an unsafe environment. When the water is flowing through your sprinkler system, turn off your water softener’s power source.

Clogged Injector

If your injector valve is clogged, the first thing to check is your injector valve. The injector has several horizontal and vertical holes that can easily become blocked with salt, dirt and sediment.

The injector valve needs to be cleaned regularly, but it’s a sensitive part so be careful when cleaning it. If you don’t want to spend your money, you can use a wooden toothpick or a toothbrush. If you have trouble freeing the blockage, then it’s time to get a new valve.

Drain Line Flow Control Clogged

The drain line flow control is located where the drains meet the main sewer line, so make sure to check it if it’s clogged

There is an internal “elbow” that connects to your water tank. If it’s in bad shape, consider whether it’s possible to replace the part.

Drain Line is Clogged or Crimped

If you’re still dealing with a salty water taste, look at the drain line in your hard water softener. This line should be free of kinks or crimps, which will allow water to pass freely.

To drain the water, use your hand to feel for the pipe and drain line. You should feel a smooth, clean path from the system’s tank to your drain. Press down to check for blockages that could cause a pipe to stop working.

One final item to watch out for is a drain line that’s too long. If your drain line is longer than 8 feet or there is more than 20 feet of pipe between your tank and the drain, then you need to make sure that your system drains correctly.

Brine Line Clogged or Crimped

Your brine tank may get clogged from all of the salt in your brine solution. Crimping the brine line can prevent the brine from running smoothly.

If the flow of water into your home isn’t even, then you could have a build-up in your system, which could lead to the water tasting salty If the cause of the leak is obvious (such as a hole in your hose), you may not need to take any other steps to fix it. You might need to buy a new part if you notice any major damage

Bad Brine Valve

The brine valve components, including the brine and downflow pistons, and the spacer stack, may become faulty. Salt in the form of brine solution is a very important ingredient for the curing of epoxy.

Drain and clean your elbow to remove the excess salt. Make sure there is no running water at the drain. If there is, replace the elbow. Most cars have several different kinds of parts in them: the engine, the transmission, the tires, and so forth. When something fails, it may not be the part that is responsible. Replace the faulty parts to solve the problem.

Excessive Water in the Brine Tank

If your water softener malfunctions, then the brine tank will probably overflow with water. A few common causes of this include bad brine circulation, clogged and blocked brine lines, and salt mushing at the bottom of the tank. A brine tank should have six inches of water in it. If the tank is full, the water is ready for salting.

Too much water can lead to excessive sodium absorption. You can empty the water with a bucket or container, or a wet vac, if you have one. You’ll need to clear any blockages or reset your system in order to prevent the problem from recurring.

Improper Programming of Control Head

The first thing you need to do when you install your hard water softener is to enter the correct settings into the control head. You must input the right information for the system to perform regeneration cycles, based on the hardness of your water.

If you’ve got mechanical programming, it can also be affected by power outages, too. This could cause a change to your pre-programmed settings, and then your pre-programmed settings could change your pre-programmed settings to change the setting you want to change.

Brine Cycle Interrupted

A regenerative water softener uses a brine solution to wash calcium and magnesium minerals out of the resin bed during regeneration. If you add up all the time it’s been taken to get the hair as short as possible and the time to get it colored.

If you stop drinking water after the cycle begins, you will end up drinking a lot of water with a high concentration of sodium ions.

Water Being Used During Regeneration

Water softeners are most efficient when they are not working for very long. If the timer is set to perform system regeneration during the day, rather than its normal time, then you might drink salty water.

You may also wake up in the night and use your water, whether to pour yourself a glass of water or to use the toilet. If you turn on your water softener while your water is running, it’s likely that salty water will enter your home’s pipes.

As soon as the water starts running out of your pipes, you’ll know what to do. Open your tap and leave it running for a few minutes, until your water is back to its usual taste.

Low Water Pressure

If your water pressure is lower than 30 PSI, it might not be flowing at a rate that is fast enough to properly get through your soft Most water softeners work best with a water pressure of between 45-70 PSI.

The hardness and pH of your water depends on where you live, the type of equipment you use to heat the water, and how often you use You can use a pressure gauge to determine if your water is under or over pressure. If you want to send water through your pipes at a faster rate, consider buying a booster pump.

Incoming Water Has High Sodium Content

You may need to replace the filter in your softener, but if this isn’t the case, it could be an issue with the incoming water If your water supply already has a high level of sodium, your water softener will just make it worse. Even the most basic water softener can be improved by monitoring and tweaking it.

Frequently Asked Questions

How much sodium should my water contain?

Hardness is measured in terms of milligrams of calcium per gallon. The exact amount of sodium that needs to be added depends on the hardness of your water. As the water becomes harder and less alkaline, it requires more sodium to balance out the water, which in turn means more sodium ions.

You can work out how much sodium your drinking water needs to contain by knowing your water hardness level in GPM. You could use this formula to calculate the amount of salt in a single serving:

For example, if you have a water hardness of 11 GPG and you add 30 mg of sodium per gallon, the calculation would look like this: 11 x 30/16 = 20.

How can I reduce sodium consumption?

Some people will tell you that they drink salt-free tap water because it tastes better. It may not taste as salty as regular tap water, but it can still cause health problems for many people. If you’re struggling with a medical condition where you need to restrict your sodium intake, try these alternatives.

Sodium sulfate is more efficient than sodium chloride. If you want to improve your laundry, buy the latter. The amount of potassium that’s in the water you drink will depend on the source and how much sodium has been added. A reverse osmosis system is the best way to achieve this.

You’ll get all of the benefits of an ultrasonic filter at a lower cost than a traditional water filter. A reverse osmosis unit is an important final point of use for drinking water after the softener. With a hardness level of 10 you’ll want to use a softener instead of a reverse osmosis.

They’re just as effective at removing calcium and magnesium from water as water softeners, and in some cases they can be more effective. You might be able to reduce your mineral content with a low-flow showerhead.

Leave a Comment